Just How to Replace a Tub
Just How to Replace a Tub
Blog Article
On this page below you'll find a bunch of amazing details pertaining to Installing A Bathtub.
Mounting a tub isn't precisely brain surgery, however it does need solid plumbing, woodworking, and also often, tiling abilities. Changing an old tub with a new one is also a moderately difficult task. If the old bathtub is easily easily accessible, the job can move quickly; if you have to open up a wall surface to eliminate the old tub and position the brand-new bath tub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will certainly require an assistant to leave the old bathtub as well as set in the new one. Make sure you have certified on your own for the work as well as are comfortable attempting it. Rather than hiring a contractor to take control of a halfway-completed task, it is much better to think about employing one prior to you start. Possibilities are you may need a professional plumber to make tube links.
This write-up will certainly assist you install a brand-new bath tub in your shower room if you have already acquired a brand-new tub and do not require to alter the arrangement of your previous water pipelines.
Your tools and product list ought to comprise the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you must do is detach the water supply. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the limited access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the taps. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. When the supply pipelines have been gotten rid of, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Prior to going on to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the installing opening in the bath/basin ensuring that the washers remain in area between the tap and also the sink. Safeguard the tap in place with the maker given backnut. As soon as the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet connectors. The former kind needs to be connected to the tap ends initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Tub
Utilizing both wood boards under its feet, position the bathtub in the required setting. The wooden boards are practical in equally spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto four little factors.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the tub up until the spirit level checks out level.
To set up faucets, fit all-time low of the outermost versatile faucet port to the proper supply pipeline by making a compression sign up with; after that do the exact same for the various other faucet.
Turn on the water system as well as inspect all joints as well as new pipework for leaks as well as tighten them if required. Fill the bathtub and also check the overflow outlet and also the regular electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling and sealing around the bath tub needs to wait till the tub has been used at least once as this will certainly resolve it into its final position.
Preparing for the Installment
To start with, the sustaining framework supplied with the bathroom needs to be fitted (if needed) according to the maker's directions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to ensure that if the tap features a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be suited its final setting.
Tiling Around the Bath tub
In the area where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to split a rigid seal, triggering the water to pass through the wall in between the bath as well as the tiling, leading to problems with wetness and feasible leakages to the ceiling below.
You can pick from a range of coloured sealers to assimilate your fixtures as well as fittings. They are offered in tubes as well as cartridges, and also are capable of securing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill up the tub with water prior to sealing, to enable the activity experienced when the bathtub is in use. The sealer can fracture fairly early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly offered on the marketplace. It is suggested to fit the tiles utilizing water-resistant or water-proof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed reading our post about How to Install a Bathtub. Many thanks for finding the time to read our posting. Be sure to take a moment to promote this blog entry if you liked it. I praise you for your time. Visit again soon.
Visit My Site Report this page